Appliance Repair in Stockton CA - (209) 231-5145

Refrigerator repair in Stockton CA

Is your refrigerator failing to properly stay cool but the freezer runs super cold?

Check internally for an accumulation of ice, which you can easily defrost by hand with a hairdryer. The issue will likely continue, but the damage to the impacted part(s) will be minimized while you wait to get your refrigerator repair done.

To try and diagnose, figure out first of all if it's the fan - does it run when the door switch is pushed in and the compressor is operational? If not, the fan is the main culprit. If the fan is not to blame, most often it will be the timer instead. Some other possible faulty parts, but not as likely, include the bimetal thermostat and heater.

What would a refrigerator repair like this cost? Of course, the specific parts to blame will have a big impact on the overall bill. A bimetal thermostat is just a few bucks but a heater can get a little more expensive. A door switch is pretty cheap, but a problematic compressor can be pricey as well. Even so, the cost of these refrigerator parts plus repair labor is not a significantly greater cost than a simple diagnostics appointment.

Washer repair in Stockton CA

What could be causing your washing machine to stop in the middle of a cycle?

Many issues could be to blame but there are a handful of reasons for this weird behavior from your appliance. We'll go over what's more and less likely to be at fault, so you will have an idea on how to troubleshoot your washer yourself.

First off, the lid switch assembly might be triggering the washer to stop. If the machine thinks the lid is open, the cycle pauses until it detects the lid is closed again. A defect in this mechanism can cause the washer to stop in the middle of a cycle. Check the lid switch for power with a multimeter and put in a new one if it fails this test.

Next, if the lid switch assembly is fine, consider whether the door lock mechanism is not latching shut properly. Any defect in the door lock can cause the machine to stop in the middle of a cycle. There are multiple switches to test for continuity, but look for physical signs of defect first.

Dryer repair in Stockton CA

Are you looking to make your dryer operate more efficiently?

Follow the practices listed below and you'll be able to better maintain your appliance. As a result, you will be more likely to avoid needing a dryer repair in the foreseeable future. Remember, the life expectancy of these machines is easily 14 years : but that's when you apply the standard maintenance expectations outlined in the owner's manual.

First off, make sure your vent pipe is the appropriate size. Using one that's too long will result in a lower efficiency usage of your dryer. The pipe should be the size instructed in your owner's manual. Also, when installing, you need to make sure not to physically damage (bend, tangle, etc.) the material.

Next, make sure the lint trap is kept clean all the time. Get into the habit to clean it out every time you start a new load. It's easy to forget when a load finishes and the machine and trap will usually be hot at that time. However, by cleaning out the lint trap before every load you will almost certainly never forget and accidentally let lint buildup. Remember, not everything stays in the trap so the more clogged it is - the greater the chance some dirt and debris escapes.

Dishwasher repair in Stockton CA

Let's go over some common issues plaguing dishwashing machines that occur in instances where the unit fails to fill properly.

For this overview, we recommend you have a multimeter on-hand if you plan to diagnose the problem yourself. If you do not own one, the cost of buying the device can run around the fee for a dishwasher repair service call.

Use your own judgment, but simply leaving the diagnosis to a professional (even if you don't get a repair) might be more financially sensible. Many DIYers will attempt to repair their dishwashers and either make a mistake installing the replacement part or simply replace the wrong part which can be a serious waste of money.

Anyhow, below are some common fill issues in dishwashers and how to check for them.

The supply hose could be clogged or tangled up. If water is unable to effectively flow through the hose the machine will be unable to fill up enough. It's possible that the obstruction or restriction causes the machine to not get any water at all. In the case of limited or no water supply, a limitation at the supply hose level is an easy to identify problem and a super quick fix.

Freezer repair in Stockton CA

What makes a freezer stop working and produce a clicking noise?

An appliance repair technician will typically check the start relay first. This part sends power to your freezer's compressor. If the relay is defective the freezer will work intermittently or not at all. The best way to troubleshoot a failing start relay in a freezer is to check for continuity. If none, or if a burnt odor is noticed, the relay will need to be replaced.

Another possible cause is a malfunction of the compressor. This part is responsible for compressing and delivering refrigerant to evaporator and condenser coils. If you check for continuity with a multimeter on the compressor pins, you want a closed circuit reading. Otherwise, the compressor will need to be replaced to get your freezer working properly again.

Oven repair in Stockton CA

Your oven must have real control over its internal temperature.

As some meals can be fatal if not fully cooked, it's undeniably important to undergo an oven repair if your appliance has heat regulation issues.

The most obvious reason for heat regulation issues would be a shorted or broken heating element. Most ovens rely on the bake or broil element (or both) to cook a meal. Set your stove to broil and see if the top heating element lights up. Set your stove to bake and see if the bottom heating element heats up. Replace either element if it fails to produce heat.

If the oven suffers from temperature regulation issues while in bake mode, the next possible cause would be a faulty igniter. However, this oven part would only be a potential culprit if you own a gas oven. For electric ovens, some other possible parts that might need to be fixed or replaced include the temperature sensor, control board and convection motor (for convection ovens).

Range/Stove repair in Stockton CA

Let's talk about the lights on your stove for a minute.

Many issues might arise involving indicator lights that simply don't work right, or it all. A hot stovetop indicator light can certainly malfunction.

First off, you might notice that the indicator light does not come on - regardless of how hot the burner gets. Alternatively, it might flicker or work sporadically but not always when it should. Or, the light might stay on all the time or for an extended period after the hot cooktop triggers the light. In almost all instances the issue is a faulty switch which is a cheap and easy replacement. But, what other issues could occur involving indicator lights on your stove?

On many models you will also find a burner indicator light for each burner. The switch can become defective, causing malfunctions, or stop working altogether. Another simple replacement of course. However, you must also consider that a problem with an indicator light could be caused by a deeper issue such as a problem with the oven's computer or circuit board.